Updated
How far each Ethernet optic reaches on OM1 to OM5 and single-mode fiber, with wavelengths and connectors, from IEEE 802.3. Optics defined by an MSA or a vendor rather than IEEE are marked. Filter by speed, fiber or the length of your run.
Maximum operating range per IEEE 802.3 (or the MSA or vendor named). The fiber grades are the ISO/IEC 11801 OM designations.
| Optic | Speed | Wavelength | Connector | OM1 | OM2 | OM3 | OM4 | OM5 | Standard |
|---|---|---|---|---|---|---|---|---|---|
| 1000BASE-SXOM1 figure is for 200 MHz·km fiber; older 160 MHz·km 62.5 µm fiber reaches 220 m. | 1G | 850 nm | LC duplex | 275 m | 550 m | 550 m* | 550 m* | 550 m* | IEEE 802.3z |
| 1000BASE-LX on multimodeA single-mode optic on multimode fiber: use a mode-conditioning patch cord at each end, as IEEE 802.3 Clause 38 describes. | 1G | 1310 nm | LC duplex | 550 m | 550 m | 550 m | 550 m | 550 m | IEEE 802.3z |
| 10GBASE-SROM1 figure is for 200 MHz·km fiber (26 m on 160 MHz·km). | 10G | 850 nm | LC duplex | 33 m | 82 m | 300 m | 400 m | 400 m† | IEEE 802.3ae |
| 10GBASE-LRMFor older multimode runs too long for 10GBASE-SR. Some links need mode-conditioning patch cords; check the module's datasheet. | 10G | 1310 nm | LC duplex | 220 m | 220 m | 220 m | – | – | IEEE 802.3aq |
| 25GBASE-SRNot specified on OM1 or OM2. | 25G | 850 nm | LC duplex | – | – | 70 m | 100 m | 100 m† | IEEE 802.3by |
| 40GBASE-SR4Four 10G lanes on four fiber pairs. The OM4 budget allows 1.0 dB of connector loss, the OM3 budget 1.5 dB. | 40G | 850 nm | MPO-12, 8 fibers | – | – | 100 m | 150 m | 150 m† | IEEE 802.3ba |
| 40G-SR4 extended reach (eSR4, CSR4)Typical vendor figures; check the datasheet of the exact module, and use the same type at both ends. | 40G | 850 nm | MPO-12, 8 fibers | – | – | 300 m | 400 m | – | Vendor |
| 100GBASE-SR10Ten 10G lanes; largely replaced by 100GBASE-SR4. | 100G | 850 nm | MPO-24, 20 fibers | – | – | 100 m | 150 m | 150 m† | IEEE 802.3ba |
| 100GBASE-SR4Four 25G lanes on four fiber pairs. | 100G | 850 nm | MPO-12, 8 fibers | – | – | 70 m | 100 m | 100 m† | IEEE 802.3bm |
| 400GBASE-SR8Eight 50G lanes on eight fiber pairs; can break out to 8 × 50G. | 400G | 850 nm | MPO-16, 16 fibers | – | – | 70 m | 100 m | 100 m | IEEE 802.3cm |
| 400GBASE-SR4.2Bidirectional: two wavelengths on every fiber, one each way. The one PHY here where OM5 reaches further than OM4. | 400G | 850 nm and 910 nm | MPO-12, 8 fibers | – | – | 70 m | 100 m | 150 m | IEEE 802.3cm |
* IEEE lists 50 µm fiber of 500 MHz·km for 1000BASE-SX; OM3, OM4 and OM5 exceed that, so they reach at least 550 m; vendors often quote more. † OM5 meets the OM4 specification at 850 nm, so it reaches at least the OM4 distance. A dash means the standard doesn't specify that fiber.
On OS1 or OS2 single-mode fiber. Long-reach links are usually limited by the optic's power budget, so check the loss as well.
| Optic | Speed | Wavelength | Connector | Reach | Standard |
|---|---|---|---|---|---|
| 1000BASE-LXMany "LX" SFPs are sold as LX/LH with a 10 km rating: that is the vendor's figure (or 1000BASE-LX10), not 1000BASE-LX. | 1G | 1310 nm | LC duplex | 5 km | IEEE 802.3z |
| 1000BASE-LX10 | 1G | 1310 nm | LC duplex | 10 km | IEEE 802.3ah |
| 1000BASE-BX10One fiber, two wavelengths: pair a BX10-U at one end with a BX10-D at the other. | 1G | 1310 nm up, 1490 nm down | LC simplex (one fiber) | 10 km | IEEE 802.3ah |
| 1000BASE-ZXNot an IEEE standard. Vendors quote about 70 to 80 km; check the datasheet and its power budget. | 1G | 1550 nm | LC duplex | 70 km | Vendor |
| 10GBASE-LR | 10G | 1310 nm | LC duplex | 10 km | IEEE 802.3ae |
| 10GBASE-ER30 km, or 40 km as an engineered link (one whose loss and dispersion have been checked against the spec). | 10G | 1550 nm | LC duplex | 30 km | IEEE 802.3ae |
| 10GBASE-ZRNot an IEEE standard, despite the name. Vendors quote about 80 km; check the datasheet. | 10G | 1550 nm | LC duplex | 80 km | Vendor |
| 25GBASE-LR | 25G | 1310 nm | LC duplex | 10 km | IEEE 802.3cc |
| 40GBASE-LR4 | 40G | 4 wavelengths, 1271 to 1331 nm (CWDM) | LC duplex | 10 km | IEEE 802.3ba |
| 40GBASE-ER430 km, or 40 km as an engineered link. | 40G | 4 wavelengths near 1310 nm | LC duplex | 30 km | IEEE 802.3bm |
| 100GBASE-LR4 | 100G | 4 wavelengths, 1295 to 1310 nm (LAN-WDM) | LC duplex | 10 km | IEEE 802.3ba |
| 100GBASE-ER430 km, or 40 km as an engineered link. | 100G | 4 wavelengths, 1295 to 1310 nm (LAN-WDM) | LC duplex | 30 km | IEEE 802.3ba |
| 100G CWDM4A multi-source agreement, not an IEEE PHY. Common and cheaper than LR4 for runs inside a campus. | 100G | 4 wavelengths, 1271 to 1331 nm (CWDM) | LC duplex | 2 km | MSA 100G CWDM4 MSA |
| 100G PSM4A multi-source agreement: four 25G lanes on four single-mode fiber pairs. | 100G | 1310 nm | MPO-12, 8 fibers | 500 m | MSA 100G PSM4 MSA |
| 100GBASE-DROften the far end of a 400GBASE-DR4 breakout. | 100G | 1311 nm (one 100G lane) | LC duplex | 500 m | IEEE 802.3cd |
| 100GBASE-FR1 | 100G | 1311 nm (one 100G lane) | LC duplex | 2 km | IEEE 802.3cu |
| 100GBASE-LR1 | 100G | 1311 nm (one 100G lane) | LC duplex | 10 km | IEEE 802.3cu |
| 400GBASE-DR4Four 100G lanes on four fiber pairs; breaks out to 4 × 100GBASE-DR. Single-mode MPO is usually angled-polish (APC). | 400G | 1311 nm (4 parallel lanes) | MPO-12, 8 fibers | 500 m | IEEE 802.3bs |
| 400GBASE-FR4 | 400G | 4 wavelengths, 1271 to 1331 nm (CWDM) | LC duplex | 2 km | IEEE 802.3cu |
| 400GBASE-LR4-6 | 400G | 4 wavelengths, 1271 to 1331 nm (CWDM) | LC duplex | 6 km | IEEE 802.3cu |
| 400G-LR4-10The 10 km "LR4" most 400G modules are sold as. IEEE's own LR4 is the 6 km 400GBASE-LR4-6. | 400G | 4 wavelengths, 1271 to 1331 nm (CWDM) | LC duplex | 10 km | MSA 100G Lambda MSA |
| 400GBASE-LR8 | 400G | 8 wavelengths near 1310 nm (LAN-WDM) | LC duplex | 10 km | IEEE 802.3bs |
IEEE 802.3 doesn't fix the connector for duplex optics; LC duplex is what SFP, SFP+, SFP28 and most QSFP duplex modules use. Parallel optics (SR4, SR8, DR4, PSM4) need an MPO/MTP trunk with the fiber count shown.
Distance is half the answer; the other half is loss. The fiber loss calculator adds up fiber, connectors and splices with TIA-568.3-D values and compares the total with these optics' IEEE loss budgets. Not sure which fiber you have? The fiber color code shows jacket and connector colors.
The module's shape sets how many electrical lanes it has, not which optic is inside: an SFP+ can be SR, LR or ZR. Speeds below are what each form factor is built for.
| Form factor | Lanes | Speed | Defined by | Notes |
|---|---|---|---|---|
| SFP | 1 | 100 Mb/s, 1 Gb/s | SFP MSA (INF-8074i) | Also comes as a 1000BASE-T copper module with an RJ45 port. |
| SFP+ | 1 × 10G | 10 Gb/s | SFF-8431 | Same size as SFP; most SFP+ ports also take a 1G SFP. |
| SFP28 | 1 × 25G | 25 Gb/s | SFF-8402 | Many SFP28 ports also run an SFP+ at 10G. Check the switch. |
| SFP56 | 1 × 50G (PAM4) | 50 Gb/s | SFF MSA | |
| QSFP+ | 4 × 10G | 40 Gb/s | SFF-8436 | Can break out to 4 × 10G where the switch allows it. |
| QSFP28 | 4 × 25G | 100 Gb/s | SFF-8665 | Breaks out to 4 × 25G. Single-lane 100G optics (DR, FR1, LR1) convert inside the module. |
| QSFP56 | 4 × 50G (PAM4) | 200 Gb/s | SFF MSA | |
| QSFP-DD | 8 × 50G or 8 × 100G (PAM4) | 400 Gb/s, 800 Gb/s | QSFP-DD MSA | A QSFP-DD port also takes QSFP28 and QSFP+ modules. |
| OSFP | 8 × 50G or 8 × 100G (PAM4) | 400 Gb/s, 800 Gb/s | OSFP MSA | Larger than QSFP-DD; doesn't take QSFP modules without an adapter. |
Whether a port accepts a slower module, or splits into breakout lanes, is up to the switch. Check its hardware guide.
Maximum channel length for each BASE-T speed, per IEEE 802.3 on TIA-568.2-D cabling categories.
| PHY | Cat5e 100 MHz | Cat6 250 MHz | Cat6A 500 MHz | Cat8 2000 MHz | Standard |
|---|---|---|---|---|---|
| 100BASE-TX | 100 m | 100 m | 100 m | – | IEEE 802.3u |
| 1000BASE-T | 100 m | 100 m | 100 m | – | IEEE 802.3ab |
| 2.5GBASE-T | 100 m | 100 m | 100 m | – | IEEE 802.3bz |
| 5GBASE-T | 100 m, depends on alien crosstalk | 100 m | 100 m | – | IEEE 802.3bz |
| 10GBASE-T | Not supported | 55 m (37 to 55 m, depends on alien crosstalk) | 100 m | – | IEEE 802.3an |
| 25GBASE-T, 40GBASE-T | Not supported | Not supported | Not supported | 30 m | IEEE 802.3bq |
Pin order and pairs: see the Ethernet cable color code.
Direct-attach copper (DAC) and active optical cables (AOC) have the module built onto each end. Short and cheap for in-rack and next-rack links.
| Cable | Length | Standard |
|---|---|---|
| 10G SFP+ passive DAC | Up to 7 m typical | Vendor SFF-8431; lengths are vendor-specific (not IEEE) |
| 10G SFP+ active DAC | Up to about 10 to 15 m | Vendor Vendor-specific |
| 25GBASE-CR (SFP28 DAC) | 5 m (25GBASE-CR-S: 3 m) | IEEE IEEE 802.3by |
| 40GBASE-CR4 (QSFP+ DAC) | 7 m | IEEE IEEE 802.3ba |
| 100GBASE-CR4 (QSFP28 DAC) | 5 m | IEEE IEEE 802.3bj |
| Active optical cable (AOC) | Commonly 1 m to 100 m | Vendor Vendor-specific: fiber with the optics fixed on both ends |
Lengths marked Vendor are what manufacturers commonly sell, not a standard limit. Switches may only accept DACs they list as supported.
300 m on OM3 and 400 m on OM4. On older fiber it is 82 m on OM2 and 33 m on OM1 (IEEE 802.3, Clause 52). OM5 behaves like OM4 at 850 nm.
About a third further: 400 m instead of 300 m for 10GBASE-SR, 150 m instead of 100 m for 40GBASE-SR4, and 100 m instead of 70 m for 25GBASE-SR and 100GBASE-SR4.
In general, no. The exception is 1000BASE-LX, which IEEE 802.3 allows on multimode up to 550 m with a mode-conditioning patch cord at each end. 10GBASE-LRM is a separate PHY made for 1310 nm on multimode. Multimode optics don't work on single-mode fiber.
Up to 55 m, and only 37 m is assured: between 37 and 55 m it depends on alien crosstalk between cables (TIA TSB-155). Cat6A supports the full 100 m channel.
TIA-568.2-D defines a 100 m channel: up to 90 m of permanent link (the horizontal cable from the patch panel to the outlet) plus up to 10 m of patch and equipment cords in total. Cat8 channels are limited to 30 m.
No. IEEE 802.3 defines 10GBASE-ER at 1550 nm for 30 km (40 km as an engineered link). ZR optics are vendor products, typically rated for about 80 km; the datasheet is the specification.
In NetworkSketch, every link records its media type, speed and the interface at each end, and the PDF export includes a cabling schedule, so the next person knows an uplink is 10GBASE-LR on single-mode without opening the rack.