Updated
Enter the switch's PoE budget and the phones, access points and cameras plugged into it. You see how much of the budget they take, whether the ports can supply each device's class, and how many more would fit. It runs in your browser.
| Device | Count | Class | Each | Total |
|---|
In NetworkSketch, each switch keeps its model and each link its ports, cable ID and length, so the diagram shows which port feeds which access point, phone and camera. Checking the cabling too? The Ethernet color code shows the pairs PoE runs on.
The power a switch port supplies for each IEEE 802.3 class (PSE), and the most a device of that class may draw at its own end (PD). The difference is what up to 100 m of cable can lose.
| Class | At the switch (PSE) | At the device (PD) | Standard |
|---|---|---|---|
| 0 | 15.4 W | 12.95 W | 802.3af (Type 1); a device that doesn't announce a class |
| 1 | 4.0 W | 3.84 W | 802.3af (Type 1) |
| 2 | 7.0 W | 6.49 W | 802.3af (Type 1) |
| 3 | 15.4 W | 12.95 W | 802.3af (Type 1) |
| 4 | 30 W | 25.5 W | 802.3at PoE+ (Type 2) |
| 5 | 45 W | 40 W | 802.3bt (Type 3), four pairs |
| 6 | 60 W | 51 W | 802.3bt (Type 3), four pairs |
| 7 | 75 W | 62 W | 802.3bt (Type 4), four pairs |
| 8 | 90 W | 71.3 W | 802.3bt (Type 4), four pairs |
802.3af (2003, often just "PoE") covers Classes 0 to 3: up to 15.4 W per port over two pairs. Enough for desk phones, badge readers and most fixed cameras.
802.3at (2009, "PoE+") adds Class 4: 30 W per port, still over two pairs. Most Wi-Fi 6 access points, video phones and PTZ cameras without heaters fit here.
802.3bt (2018) uses all four pairs. Type 3 adds Classes 5 and 6 (up to 60 W), Type 4 adds Classes 7 and 8 (up to 90 W). It covers newer access points, heated outdoor cameras, thin clients and PoE lighting. Names like "PoE++" are marketing terms; some older 60 W ports predate 802.3bt, so check that the switch says 802.3bt if the devices need it.
A port negotiates down: a PoE+ port powers an 802.3af phone at its class. Going the other way, a device that needs more than the port offers may start with reduced features or not start at all.
Without more information, a switch reserves each port's full class power when the device connects, so a Class 4 access point takes 30 W of the budget even while it draws 14 W. That is the safe way to plan, and it is the default here.
With LLDP power negotiation (LLDP-MED or the 802.3 power TLVs), the device tells the switch how much it needs and the switch can allocate that instead. Whether a switch does this, and whether it adds a margin for cable loss on top, depends on the model and its settings. Plan by class unless you know the switch allocates by negotiated power, and use measured figures from the switch's own PoE status output where you have them.
The PSE figures in the table already allow for the worst case: 100 m of twisted-pair cable. Shorter runs lose less, but switches allocate by class regardless of length, so length doesn't change the budget.
More power means more heat in the cable, and large bundles of high-power runs warm up, which raises resistance and loss. TIA TSB-184-A gives guidance on bundle sizes for PoE. Use Category 5e or better for any PoE; for big bundles of 802.3bt runs, cable with thicker conductors (such as 23 AWG) runs cooler. The Ethernet color code page shows which pairs carry power in each mode.
Many Wi-Fi 6 access points are Class 4: 30 W at the switch port, 25.5 W at the AP. Many Wi-Fi 6E and Wi-Fi 7 access points ask for 802.3bt power (Class 5 or 6) to run every radio and port, and some run on PoE+ with reduced features, such as fewer radio streams or a disabled USB port. The access point's datasheet lists its class and what changes on less power.
When it budgets by class, the switch sets aside the class's full port power, which covers the device's maximum plus the loss in up to 100 m of cable. A Class 4 access point gets 30 W even if it draws 14 W. Switches that support LLDP power negotiation can allocate what the device asks for instead, which often frees a lot of budget.
A common rule of thumb is about 20% of the budget. It is not a standard. It covers devices added later, devices that draw more after a firmware or feature change, and switches whose budget drops when one of two power supplies fails. The switch's datasheet lists the budget for each power supply option.
802.3af (PoE) gives up to 15.4 W per port, 802.3at (PoE+) up to 30 W, both over two pairs. 802.3bt gives up to 60 W (Type 3) or 90 W (Type 4) using all four pairs. A newer switch powers older devices; an older switch may power a newer device only at reduced power, or not at all.
No. The calculator runs on this page in your browser, and the page has no analytics or tracking. What you enter is kept in the part of the link after the # so you can share it, and browsers never send that part to the server.